Add an entry to discovery.xml with the urlsrc where capabilities end
point can be found. Use json format to send back the feature list.
Change-Id: I390a53d956d53ca79e5a8090aead7f4131ec4ca0
We try to decrease the network usage with avoiding sending out
to much tiles to the client. When we already sent out two versions
of the same tile without having the tileprocessed message from the
client we delay sending out the next version to avoid spamming tiles
on the network.
Change-Id: Ia47cd7c0d3fb829f6777f0c3265970433591df19
POST requests require the full request to be
left in the socket buffer to be parsed in full.
But GET requests, especially WS upgrade, must
have the request cleared from the socket, as
there is more data expected to be read after
the upgrade, which happens by the DocBroker
thread, so clearing the buffer must be done
before the upgrade.
This patch accomodates these two conflicting
cases and refactors the code slightly to
make it more structured and readable.
Change-Id: Ia7357a745a3900f986099ba14af2a0946023018b
Reviewed-on: https://gerrit.libreoffice.org/36873
Reviewed-by: Ashod Nakashian <ashnakash@gmail.com>
Tested-by: Ashod Nakashian <ashnakash@gmail.com>
This was a workaround to Poco's limitation
of requiring socket receiveFrame be given
preallocated buffer, which couldn't be
exceeded by a larger payload. This meant
the receiver had to know the maximum
payload in advance.
Since only the Kit uses Poco sockets,
and the Kit never receives large payloads,
this preamble is now obsolete.
100% (94/94) of old-style tests PASS.
Change-Id: I76776f89497409e5755e335a3e25553e91cf0876
Reviewed-on: https://gerrit.libreoffice.org/36037
Reviewed-by: Ashod Nakashian <ashnakash@gmail.com>
Tested-by: Ashod Nakashian <ashnakash@gmail.com>
These are really GET requests that aren't
WebSocket upgrade. Should rename to something
less misleading.
Re-enabled testSlideShow which depended on this.
Change-Id: I52b7f67b650fcdcbae7c2bff020b756099263141
Since we always need to set the thread-pool size
anyway, we cannot have 'unlimited' connections.
Actually, we never did, so that was misleading
in configure.ac anyway.
The current defaults are 20 connections and
10 documents, instead of the previous 1024
connections.
The reason for this "low" limit is to
enable unittesting these limits automatically
for the default configure.
There is also a lower-limit (needed by unittests
and internal technical requirements) of 3 connections
and 2 documents.
Change-Id: I6ccf3a607c50bb2a86bf1c0a16ebb6326ee34c7d
Reviewed-on: https://gerrit.libreoffice.org/32712
Reviewed-by: Ashod Nakashian <ashnakash@gmail.com>
Tested-by: Ashod Nakashian <ashnakash@gmail.com>
Messages larger than a certain size are preambled
with a 'nextmessage' message that hold the size
of the subsequent message.
This is a workaround to a limitation the Poco
WebSocket API where if the buffer size is
smaller than the received frame the socket
ends up in a bad state and must be closed.
Unfortunately the new API that avoids this
workaround is not yet released by Poco.
Here we minimize the need for 'nextmessage'
to truely large messages. The limit is now
raised from above 1KB to over 63KB.
We may raise this limit further, but that will
cost each socket that much dedicated buffer size.
Change-Id: I01e4c68cdbe67e413c04a9725152224a87ab8267
Reviewed-on: https://gerrit.libreoffice.org/31286
Reviewed-by: Ashod Nakashian <ashnakash@gmail.com>
Tested-by: Ashod Nakashian <ashnakash@gmail.com>
