#
# This file is part of the LibreOffice project.
#
# This Source Code Form is subject to the terms of the Mozilla Public
# License, v. 2.0. If a copy of the MPL was not distributed with this
# file, You can obtain one at http://mozilla.org/MPL/2.0/.
#
# This file incorporates work covered by the following license notice:
#
# Licensed to the Apache Software Foundation (ASF) under one or more
# contributor license agreements. See the NOTICE file distributed
# with this work for additional information regarding copyright
# ownership. The ASF licenses this file to you under the Apache
# License, Version 2.0 (the "License"); you may not use this file
# except in compliance with the License. You may obtain a copy of
# the License at http://www.apache.org/licenses/LICENSE-2.0 .
#
WINDOWS ONLY, no other platforms
This test checks if the cli assemblies and their policy files are installed in the
GAC and if the policy files are correct. The office must be installed with complete
system integration. That is, one does not use setup /a for starting the
installation.
In OOo 3.0 there was a breaking change so that the test created for previous
version do not work anymore. To use these old tests one needs to install a
version of OOo less than v 3.0. Then one needs to check out the cli_ure module
for that version. The tests are contained in cli_ure/qa/versioning.
In the sub directory version_libs are libraries which are linked with (referencing)
cli_cppuhelper
cli_basetypes
cli_ure
cli_uretypes
cli_oootypes
They are named version_3_0_0 etc, where the name indicates the version of the
office for which they were initially build. If there are only the assemblies
for example OOo2.0.2 installed and a client was build with the assemblies from
OOo2 then the policy assemblies must make the correct redirection.
When calling dmake then the executable runtest.exe and version_current.dll are
build. When runtest runs then it loads all dlls, which names start with
"version", from the same directory and tries to run a particular test code
which is only available in the version_xxx.dll s. The code in the
version_xxx.dlls uses the cli default bootstrap mechanism to find the office
installation and start the office. When running runtest in a build environment
then it may use the wrong libraries for bootstrapping in which case the test
fails. Then one has to set PATH which must point to the program directory of
the office installation. For example:
set PATH=d:\office\program
runtest stops when a test failed to run. It writes error information to the
console which shows which version_xxx.dll failed to run and if this was due to
a referenced assembly that could not be loaded. This would be the case if such
an assembly or the policy assembly is not properly installed or the redirection
in the policy assembly is wrong.
The version_current.dll references the assemblies in the current build
environment. version_current.dll is also executed when runtest is started.
To run the whole test one can either
1. start testools/wntmsci11.pro/bin/runtests.exe in a console where no
environment is set.
2. Call dmake run in testools/qa/cliversions
For a limited test one can call in this directory
dmake run office=d:\office
There must not be an office installed in the system (the assemblies from the GAC
would then be used). Only the test with the version_current.dll will succeed
because there are no policy files installed. This test requires that all
assemblies are copied next to runtests.exe - the makefile will do that.
The parameter office must be a system path to the office installation
directory. The java code calls runtest and also sets PATH so that the test
works in the build environment. It also sets UNO_PATH so that the office will be
found. If the test says that it failed, then one should run runtest directly
because it puts out more information.
Creating a new version_xxx.dll
==============================
When a version of our assemblies changes then one should provide a new version dll which test exactly the assemblies with the changed version. This is easily done:
1. set the build environment in which the new versions are effective.
2 call: dmake name=version_xxx.dll
3. copy the new version dll from the output tree into qa/versioning/version_libs
4. commit the new version.dll using the -kb switch (only when creating the new file : cvs new -kb version_3_1_0.dll)
abf17ce647